Усилители мощности

Подключите этот мощный усилитель Marantz MM7025 к выходам предусилителя вашего ресивера для раскрытия всего потенциала системы.

Выходная мощность составляет 170 Вт на канал при 6 Ом
Дискретная схема обратной связи по току для точного звука на любой громкости
Сверхмощный тороидальный трансформатор питания для стабильного тока
Один вход RCA и один балансный вход XLR для каждого из каналов

Designed for multiple stereo setups, the C 268 can be used in a variety of scenarios, including traditional stacks with a preamplifier or for bi-amping your favourite loudspeakers.

80W x 2 Continuous Power into 8 or 4 Ohms,Stereo Dynamic Power 120/200/250---8/4/2 Ohms
Balanced Line Inputs,Single-Ended Line Inputs.Variable Input Level Control
Line Output for Daisy Chaining.12V Trigger In/Out.Auto Turn-on with Selectable Threshold

Selectable balanced inputs make the C 298 a natural for studio use or connection to High End Preamps and Processors. These inputs include a trim control useful for matching to other components.

Stereo Dynamic Power 260/490/570W-- 8/4/2 Ohms,Balanced Line Inputs
Single-Ended Line Inputs,Input Level Control,Line Output for Daisy Chaining
12V Trigger In/Out,Auto Turn-on with Selectable Threshold,Ground Lug

This amp pushes Class D amplification performance to new limits thanks to HybridDigital Purifi Eigentakt  technology.

200 watts per channel into 8 ohms,380 watts into 4 ohms
4-ohm stable for use with a wide range of speakers
innovative HybridDigital Purifi Eigentakt™ technology
three-position gain switch on back panel (low, mid, and high)
frequency response: 20-20,000 Hz,2 balanced XLR inputs 

A completely new combination amplifier was developed for the SP-T700, exploiting the respective advantages of tubes and transistors in an innovative manner, combining them to create a harmonious whole.

Frequency Response: 20 Hz – 20 kHz,Inputs: 1 x Mono RCA
Nominal Output Power RMS / 8 Ohm: 150 Watt
Nominal Output Power RMS / 4 Ohm: 300 Watt
Tubes: 1 x 6S3P-EV; 1 x 6SCH9P, 1 x 6Z4

Two additional 6N16 tubes were added to the input section to make the sound signal more warm dn natural. The VU-meters with user selectable colored backlighting complete the timeless design.

Frequency Response: 20 Hz - 20 kHz,Tubes: 2 x 6N16, 1 x 6N15
Nominal Output Power RMS / 8 Ohm: 2 x 150 Watt
Nominal Output Power RMS / 4 Ohm: 2 x 250 Watt
Inputs: 1 x Stereo RCA, 1 x Stereo XLR

With a power rating of more than 1,1 kW in 8 ohms, it is on the verge of being easier to measure the H30A in horsepower. The massive H30A mono power amplifiers from Hegel play any loudspeaker in the world with ease and authority.

Power output: 1100 W/8 Ω,Dual Mono,SoundEngine
RCA & XLR Inputs,> 500 Damping Factor,56 Bipolar Transistors

The AP-505 is a versatile stereo power amplifier based around a high-performance, TEAC-tuned, Hypex Ncore power amplifier module, housed within a compact and elegant case.

Hypex Ncore power amplifier module, tuned by TEAC
130W + 130W of max output power, or 250W in BTL/bridged mode
Can operate in Stereo, Bi-Amp and BTL/bridged modes
Fully balanced circuit design,Passive-cooling for silent operation
A4-sized footprint and full-metal body for rigidity, stability a..

Dual mono power amplifier with fully balanced structure and two custom made Hypex Electronics Ncore power amplifier modules

High output with a practical maximum of 260 W + 260 W (4Ω) /
Dual mono design throughout entire system,Clean signal amplification
Two independent left/right high-capacity toroidal core power supply transformers
Discrete buffer amplifiers used in the input stage,Fan-free design to minimize noise

The M-5000 embodies this spirit with time-honoured craftsmanship and market-leading innovation and serves as the epitome of high-fidelity audio reproduction.

200 W + 200 W (4 ohm, 20 Hz-20 kHz, 0.07% THD, 2-ch driven)
Meticulously designed, balanced signal transmission
Floating and balanced power amplifier layout for improved drivability
Low impedance design with shortened signal and power supply paths
Improved construction delivers state-of-the-art rigidity,Mas..

The Donizetti Anniversary power amplifier, designed by Airtech laboratories, proposes another of the historic products of Audio Analogue.It’s a high power stereo power amp: with its 250W on 8 ohms that double by halving the impedance is able to drive perfectly any speaker.

Channels: 2,RCA inputs: 1,XLR inputs: 1
Input impedance: 47Kohm,Power on 4 ohms load: 500
Frequency Response(Att. 0dB, -3dB band): 110KHz

The Delta STEREO distills all of Class' innovation and knowledge into a compact high-performance stereo amplifier.In situations where dual mono amplifiers can't be accommodated, Delta STEREO offers uncompromizing performance in a single component.

250W per Channel total,Massive, high-quality power supply
Custom toroidal transformer,Custom-made Navcom feet to absorb vibrations
6-layer circuit boards provide for shortened signal
Furutech rhodium-plated RCA and torque..

Delta MONO delivers the utmost clarity in everything you hear.Every detail communicates natural, authoritative sound.An expansive dynamic range with infinitesimal noise delivers unsurpassed fidelity to the musical source. Start listening.

300W per unit total,Massive, high-quality power supply
Custom toroidal transformer,Hand-laid circuit boards
6-layer circuit boards provide for shortened signal
Fully balanced output stage and balanced circuitry
22 4-pole Mundorf capacitors..

The dual monoblock architecture is equipped with twin, custom engineered oversized, in-house manufactured 2,200 Volt Amp toroidal transformers in individual epoxy filled enclosures eliminating noise and vibration.

Balanced XLR inputs,Class AB linear power amplifier
500 watts of robust power x 2 at 8 ohms
800 watts x 2 at 4 ohms,Dual custom engineered toroidal transformers

The main reason Class D is gaining in popularity is its high efficiency- it delivers more of the power fed into it as musical signal output. This efficiency reduces heat and the need for large heat sinks, resulting in very powerful amps that are relatively compact and lightweight.

200 watts per channel into 8 ohms,400 watts per channel into 4 ohms
proprietary UFPD 2 Class D amplifier technology
high-efficiency, low-noise switching power supply with APFC
stereo bal..

Colossal power and breath taking performance. Never has an amplifier been so close to perfection, but at the same time the technology must be subordinate – and transparent – to the music.

Audio grade “switched mode” power supply (4 × 600 VA )
More than 1,000,000 µFarad storage capacity in the power supply unit
Peak current rating of more than 120 Ampere
Power output  600W at 8 ohms,1200W at 4 ohms
Inputs 1 × balanced (XLR),1 × unbalanced (RCA)

The new “switched mode” power supply technology brings the soulution 711 to new level of performance. Improvements on the test bench get confirmed by the performance in the listening room.

Audio grade “Switched Mode” power supply (4 × 600 VA )
More than 1,000,000 µFarad storage capacity in the power supply unit
Peak current rating of more than 120 Ampere
Power output 2 × 150W at 8 ohms,2 × 300W at 4 ohms
Inputs: 1 × balanced (XLR),1 × unbalanced (RCA)

The 511 is equipped with the same “switched-mode” power supply technology, optimized for audiophile applications, as our series7 products.

versatile: stereo-, mono- and dual-mode
Stereo-mode: 140 W @ 8 Ω, 280W @ 4 Ω, 560W @ 2 Ω per channel
Dual-mode: 140 W @ 8 Ω, 280W @ 4 Ω, 560W @ 2 Ω per channel
Mono-mode: 560 W @ 8 Ω, 1120 W @ 4 Ω, 2000 W @ 2 Ω

Cyrus Power XR power amplifier is a flagship stereo power amplifier in the XR range and is a perfect match for the XR Pre or indeed for any other Cyrus amplifier with a 'Pre Out' as an upgrade option.

Power Output - 2 x 144W into 4 Ω,Power Output - 2 x 110W into 6 Ω
Power Output - 2 x 87W into 8 Ω,Input impedance - 28kΩ

The Classic POWER is the latest power amplifier from Cyrus, designed for the new Classic series. The objective was to create a significant step up in performance from previous Classic amplifiers by using everything that we learnt when developing the fantastic XR Series.

Power Output - 2 x 110W into 6 Ω,Power Output - 2 x 87W into 8 Ω
Unbalanced (RCA) inputs (with daisy-chain out)
Balanced (XLR) inputs,12V trigger input
PSX-R2 upgrade connection,Firmware upgrade por..

Rotel engineered this amplifier to deliver nuanced sound in a stereo music system, but you can also use it to drive one pair of speakers in a multi-channel home theater system.

130 watts per channel into 8 ohms with 2 channels driven
4-ohm stable for use with a wide range of speakers
Class AB amplifier design,custom-made toroidal transformer
stereo balanced XLR and unbalanced RCA inputs

The Rotel RB-1582 MkII provides up to 200 watts per channel, and it's 4-ohm stable, so it's compatible with a wide array of speakers. It has a custom-designed toroidal transformer inside, regulated by high-quality, British-made capacitors.

4-ohm stable for use with a wide range of speakers
Class AB amplifier design,custom-made toroidal transformer
stereo balanced XLR and unbalanced RCA inputs
two pairs of 5-way binding post speaker connectors

It delivers plenty of power to "get loud," and offers exquisite control over the stop/start motion of speaker drivers, for dynamic realism and accuracy.

350 watts per channel into 8 ohms with 2 channels driven
4-ohm stable for use with a wide range of speakers
Class AB amplifier design,high-quality, British-made capacitors
stereo balanced XLR and unbalanced RCA inputs

Усилитель Anthem STR Power использует проверенный класс AB и отобранные вручную транзисторы, чтобы передать всю энергию и динамику вашей музыки без искажений.

Мощность 400 Вт на канал при 8 Ом и 600 Вт при 4 Ом.
Два массивных тороидальных БП для стабильной и бесшумной работы.
Технология Advanced Load Monitoring и стрелочные индикаторы мощности.
Автоматическое включение, балансные входы XLR и выходы RCA.

Fully discrete circuitry with high current toroid transformer.Bridging switch for stereo or mono operation.

90 watts x 2 into 8 Ω (all channels driven)
150 watts x 2 into 4 Ω or 2 Ω (all channels driven)
Two pairs of speaker outputs with front panel A/B buttons
DC Servo and relay protection circuits

This power amplifier effortlessly delivers delicate audio signals from a preamplifier to loudspeakers with absolute transparency and finesse.

No Global Feedback Design,MOON Transistors
Dual Mono Configuration,Monaural Mode Toggle Switch
Output Power (Stereo 8 Ω): 200 W
Output Power (Mono 8 Ω): 600 W
Frequency Response: 2 Hz – 100 kHz

The 400M delivers finesse, detail and refinement that can challenge your perception of reality vs. recorded music.

Fully balanced differential circuitry.
Optimised selection of very high quality electronic components.
Output Power at 8Ω 400 W,Output Power at 4Ω 650 W
Frequency response 10Hz - 125kHz

Vocals and cymbals float in a musical space filled with the air and natural ambience of a musical performance.

Balanced differential circuitry.
Optimised selection of very high quality electronic components.
Output Power at 8Ω: 125 W per channel
Output Power at 4Ω: 250 W per channel
Frequency response: 10Hz - 125kHz

Updated rear panel with heavy duty speaker terminals from HINT 6

160 watts x 2 at 8 Ω ,240 watts x 2 at 4 Ω
Circuitry designed by legendary John Curl
Gold-plated RCA input loop output jacks
JFET input stage, MOSFET driver stage
Independent power supplies for input stage,driver stage and output stage

Five Channel Power Amplifier.Class A/AB circuitry designed by legendary John Curl.DC Servo and relay protection circuits

180 watts RMS x 5 at 8 Ω,255 watts RMS x 5 at 4 Ω
Balanced XLR inputs with discrete circuits
Heavy-duty 24k gold-plated, 5-way speaker terminals

Three-Channel Power Amplifier.Complementary MOSFET driver stage and JFET input stage

250 watts x 3 at 8 Ohms / 400 watts x 3 at 4 Ohms
Adjustable gain,Circuitry designed by legendary John Curl
Unbalanced RCA and balanced XLR inputs
DC Servo and relay protection circuits,THX Ultra2 certified
Heavy-duty 24k gold-plated 5-way speaker terminals

Разработанный в сотрудничестве с командой Starke Sound, Eversolo AMP-F2 представляет собой высококлассный усилитель класса D на базе инновационного модуля NS600.

Выходная мощность составляет 280 Вт на канал (4 Ом) и 130 Вт на канал (8 Ом)
Эффективная технология класса D обеспечивает выдающуюся динамику
Балансный 2-канальный вход XLR для чистого прохождения сигнала

Если в вашей двухканальной аудиосистеме используется требовательная к питанию акустика, Arcam PA240 обеспечит её всей необходимой мощностью.

Выходная мощность: 225 Вт на канал при 8 Ом (380 Вт на канал при 4 Ом)
Высокоэффективное усиление класса Class G для идеальной динамики и чистоты
Три режима работы: Stereo, Dual Mono или мостовой режим (Bridged)
Переключаемые входные разъемы: RCA или балансные XLR
Бескомпромиссный контроль даже для самых тяжелых напольных к..

To achieve an optimum of sound quality, performance and efficiency, we have developed a completely new circuit topology.

Nominal power per channel: 250 Watts at 4 Ohms
Extremely low distortion factor and intermodulation distortion at all power levels
Extraordinarily low noise,High damping factor,Clean clipping
Totally linear frequency response up to 60 kHz

The amplification circuit of the 312 is based on the technology used in our Series 5 amplifiers.

Power output 120 W at 8 ohms,240 W at 8 ohms
Analog inputs 1 × balanced (XLR)
LINK (remote turn-on) 2 x phone jack (3.5mm)
Loudspeaker 2 pair loudspeaker binding posts

Further features include two modified power supplies for increased performance, plus an additional auxiliary power rail for the front end, which provides extra voltage to drive the custom-made MOSFETs.

Trickle down ULTIMA tech,Dual feed-forward error correction
Fully balanced system,HF Switch mode power supply
Proprietary MOSFET, power 75W*2 into 8 ohms

The outstanding performance of the QUAD 303 is still celebrated to this day, and is largely due to the unique output circuit developed by QUAD.

QUAD 303 Triples output stage,Dedicated 200VA toroid transformer
Stereo/Bridge mode switching,Inputs: 1 x Line, 1 x XLR
Rated power: Stereo: 2 x 70W at 4 ohms

Envelope yourself in a sonic landscape defined by its sure-footed,visceral sound, where smooth vocals and airy upper-end extension reign supreme

Power Output: 2 x 200 watts at 8 Ohms,2 x 350 watts at 4 Ohms
Frequency Response: 10Hz- 50KHz,Audio Input: 2 RCA, 2 XLR
Audio Output: 2 pairs of heavy-duty, gold-plated binding posts

The heart of this audiophile amplifier is a Class D module which is highly efficient and energy saving.

100 watts per channel into 8 ohms,140 watts into 4 ohms
stereo analog RCA input and output
12-volt trigger input and output for custom integration
vibration-resistant aluminum chassis

Our Monogrammed Heatsinks add visual appeal and will keep the MC830 running cool for optimum performance.

300 watts x 1 into 8 ohms ,480 watts x 1 at 4 ohms
industrial design featuring an open, polished stainless steel chassis
McIntosh Monogrammed Heatsinks add visual appeal
frequency response:10-100,000 Hz ,balanced XLR input,unbalanced RCA input

The CAD-120S MkII is a fully balanced stereo tube amplifier that masterfully blends power with precision for an unparalleled auditory experience.

Circuit Type: Class AB,push-pull amplifier
Ultralinear or Triode mode operation with a front panel selector switch
Power Output: Ultralinear - 120 watts per channel,Triode - 60 watts per channel
Inputs:XLR balanced or RCA single-ended,Frequency Response:17 Hz – 25 KHz

The MC152 delivers all the bass slam you could ask for, serving as the foundation of its big,detailed,involving sound.

150 watts per channel into 8, 4, or 2 ohms (20-20,000 Hz) with 2 channels driven
stereo balanced XLR and unbalanced RCA inputs
push-pull complementary Class AB design for signal purity
oversized power transformer and extra-large capacitors for stable,noise-free operation
Power Guard monitors,fiber optic illuminated glass front panel